Department of Training and Workforce Development - Northam Central Regional TAFE - Block C - Female Toilet/Shower, Universal Access Toilet Refurbishment

Closes in 3 daysSubmission deadline: 21 October 2026, 02:30 PM Australia/Perth

About this tender

This Tender is restricted by the Issuer. Overview The Department of Housing and Works (WA) is seeking a contractor to undertake refurbishment works to the Female Toilet/Shower and Universal Access Toilet (UAT) in Block C at Central Regional TAFE's Northam Campus, on behalf of the Department of Training and Workforce Development. Scope The scope includes works to the Block C Female and UAT Toilets as follows: Demolition – General – Female and UAT Toilets Remove and dispose of all existing floor and wall tiles Remove and dispose of existing toilet suites Remove and dispose of existing toilet partitioning and doors Remove and dispose of hand wash basins and tapware Remove and dispose of all shower tapware and rose Remove and retain toilet roll holders for re-use Remove and dispose of mirrors Remove and retain soap dispensers for re-use Remove and retain paper towel dispensers for re-use Remove and retain female sanitary product dispenser for re-use Remove and retain accessible handrail in the UAT for re-use Remove and dispose of existing light fittings Remove and dispose of existing skylights and diffusers Remove and dispose of any existing extraction/exhaust fan, grilles and accessories Remove and dispose of signage on all external doors Retain all existing external doors and hardware Make good all affected surfaces from demolition works Decommission all services to fixtures outlined to be demolished Flooring Re-level floors to ensure falls are towards floor wastes, including levelling the shower floor so there is no longer a lip Install new chrome plated floor wastes finishing flush with the floor tiles Carry out waterproofing works in accordance with AS 3740 and manufacturer's recommendations Install new 300mm x 300mm non-slip floor tiles (R10 rating) with matching grout to all floor areas, including a half tile skirting, with colour to be determined by Central Regional TAFE Walls – Toilets and Shower Carry out waterproofing works in accordance with AS 3740 and manufacturer's recommendations Install 300mm x 600mm wall tiles to the rear toilet walls, shower change wall and shower cubicle walls Paint all other walls with one coat sealer and two coats paint in Dulux Lexicon Half, to be confirmed by Central Regional TAFE Ceilings Apply paint finishes consisting of one coat sealer and two coats white, mould resistant ceiling paint Toilet/Shower Partitioning Supply and install new laminate toilet and shower partitions, doors and associated hardware to match the existing layout or approved equivalent, with the external shower partition full length to floor as per existing Supply and install one shower change area bench, approximately 800mm Colours to be Charcoal Grey walls and Leon Hickory doors or equivalent, to be confirmed by Central Regional TAFE Toilets Supply and install 2 new toilet pans with soft-close seats and lids Remove and replace existing concealed cisterns located within the service duct and provide new wall-mounted dual-flush actuator plates Shower Taps and Rose Supply and install new chrome-plated shower taps (or mixer) and a water-efficient shower rose Toilet Roll Holders Re-install the retained toilet roll holders Handbasins Supply and install 2 wall-hung vitreous china handbasins as specified or approved equivalent Cap existing redundant water and waste services and install new service pipes to accommodate the new handbasins Tile above the handbasin to one tile high to the base of the mirror Handbasin Taps Supply and install 2 basin mixer taps as specified or approved equivalent Vanity Mirrors Supply and install 2 x 900mm x 600mm stainless steel framed mirrors above the vanity basins, at a height to be determined on site Soap Dispensers Re-install the retained soap dispensers, with the installation location to be determined once the handbasins are installed Paper Towel and Sanitary Product Dispenser Re-install the retained paper towel dispenser units, with locations to be determined on site Re-install the retained female sanitary product dispenser in the female toilet External Doors Repair, patch and paint all internal and external doors and frames, with colour to be determined by Central Regional TAFE Retain and reinstall existing door hardware (handle and lock) Install new door signage (client supplied) Electrical Supply and install 2 new 1200mm LED light fittings Supply and install 1 new 200mm x 200mm exhaust fan servicing the female toilet/shower area, ducted and vented to the exterior in accordance with NCC requirements and relevant Australian Standards Allow for all associated electrical connections, wiring, switches, ductwork, grilles, penetrations, mounting hardware, commissioning and testing to ensure a complete and operational installation Contractor Requirements Waterproofing works must be carried out by a licensed waterproofing contractor in accordance with AS 3740 and manufacturer's recommendations, with a waterproofing certificate provided upon completion Tender Briefing and Site Inspection A site visit will be held for this opportunity. Date: 13 Oct, 2026 Time: 10:00 AM Location: Central Regional TAFE - Northam Campus, Northam To confirm attendance at this site visit, contact Donna Crook on (08) 90416302 or by email Donna.Crook@dohw.wa.gov.au by 2:30pm on 12 September 2026. Enquiries Contact: Donna Crook, Senior Project Officer Phone: (08) 90416302 Mobile: 0429411547 Email: Donna.Crook@dohw.wa.gov.au

How to respond to this tender

A strong tender response is clear, compliant, and backed by evidence. These steps apply to most Australian and New Zealand public tenders.

Read the requirements in full

Open the official listing and download the full tender pack. Note the response schedules, evaluation criteria, mandatory conditions, and the exact closing time and lodgement method.

Confirm you are eligible and it is worth bidding

Check licences, insurances, certifications, and any conformance requirements before you commit. A quick bid or no-bid decision saves days of wasted effort on a tender you cannot win.

Answer every criterion with evidence

Respond to each evaluation criterion directly and back your claims with concrete examples, referees, and past performance. Address the buyer’s stated need, not a generic capability statement.

Lodge early through the official portal

Submit through the source portal well before the deadline. Late or incorrectly lodged bids are almost always rejected, so leave time for uploads, portal errors, and last-minute questions.

Ready to write winning tenders?

Sign up today, what a relief.

Sign up

Similar public opportunities

Review the lifecycle label on each related notice to see whether submissions are open.